ttamamusually replies in minutes11:00
pinnedfrom AED 150–600visit length 1–3 hourslocation University City, Sharjahvendors verified
need wiring repair in university city — today if possible11:00✓✓
Whether it's a one-off or something you'll need regularly, electrician in University City works best when the vendor is verified, the price is visible, and rebooking is one tap.11:01
typical ranges vendors quote around university city —Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250Light fixture or ceiling fan installation, standard ceilingAED 150–350Chandelier installation with assembly, high ceilingAED 350–60011:02
that works. who actually turns up?11:03✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:04
What you should expect to pay
Rather than publishing one rate, tamam shows what multiple verified vendors charge for wiring repair so you can pick the tier that fits the job and the budget.
Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250
Light fixture or ceiling fan installation, standard ceilingAED 150–350
Chandelier installation with assembly, high ceilingAED 350–600
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
Villa landscape lighting repair visitAED 250–550
What you finally pay depends on the vendor and tier you choose — all of it visible before booking.
The landlord between tenants: a two-hour audit that prevents deposit disputes
The gap between tenancies is the only time you have an empty unit, full access and no one to inconvenience, which makes it the cheapest possible moment to deal with electrical wear. Faults found now cost a call-out; the same faults found by an unhappy tenant in month two cost a call-out plus an argument about liability, and unresolved snags are a recurring theme in deposit disputes at the rental committees.
A competent electrician can audit a one- or two-bedroom flat in a couple of hours: test every socket with a tester, press-test each RCD, check water heater elements for earth leakage before they become the next tenant's mystery trip, tighten DB terminals that loosen with thermal cycling, replace yellowed or cracked switch plates, and label the DB so the next occupant is not flipping breakers at random. In villas, add the garden circuits and the external water heater cupboards, which bake in the sun.
Where a handyman stops and an approved contractor begins
UAE utilities draw a firm line through every home. DEWA, SEWA, ADDC and Etihad WE own and control everything up to and including the meter; nobody you hire may touch it, and a damaged meter seal alone can trigger penalties. Beyond the meter, the rule of thumb is that like-for-like work is handyman territory while anything that changes the installation needs a contractor holding the relevant utility approval: replacing or upgrading the DB itself, adding new circuits, rewiring, increasing the connected load for a bigger AC or an EV charger, or anything the utility must inspect and reconnect.
Handyman-level work, which most tamam electrical bookings fall into, covers fault finding, socket and switch replacement, adding a socket as a spur on an existing circuit, light fixture and fan installation, water heater replacement on an existing point, and appliance connections. The technician should still be a trained electrician; handyman-level describes the regulatory weight of the job, not the skill it needs.
Common missteps
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Fixing nuisance trips by fitting a bigger breaker or a less sensitive RCD
Upsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Frequently asked questions
Why does my breaker trip every time it rains or the humidity spikes?
Moisture is getting into an outdoor fitting, balcony socket, external water heater cupboard or garden joint and leaking current to earth, which the RCD correctly detects. It feels random because it follows weather, not usage. An electrician isolates circuits at the DB and tests insulation resistance to find the wet point, then re-terminates it in a properly sealed enclosure.
How long does light fixture installation take, and can I supply my own fixture?
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
What is an RCD, and why does mine trip when the washing machine runs?
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
How do I know the electrician I am booking is actually qualified?
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Is it worth adding RCD protection to an older building's board?
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
Do you cover University City?
We cover University City and the surrounding Sharjah communities. Message on whatsapp if you want a specific time confirmed first.