ttamamusually replies in minutes11:07
pinnedprice band AED 150–600duration 1–3 hourscovers The Villa Projectemirate Dubai
need wiring repair in the villa project — today if possible11:07✓✓
tamam covers The Villa Project for electrician the same way it covers every UAE community: multiple vetted vendors, AED ranges you can see up front, and booking that takes a couple of taps.11:08
typical ranges vendors quote around the villa project —Socket or switch replacement, per pointAED 150–250New socket point as a spur on an existing circuitAED 180–350Chandelier installation with assembly, high ceilingAED 350–60011:09
that works. who actually turns up?11:10✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:11
Start at the DB board: what a trip is actually telling you
Every UAE home has a distribution board (DB), usually a grey or white panel near the entrance or in the corridor. Inside sit a main isolator, one or more RCDs (residual current devices, the wide switches with a test button) and a row of MCBs, the small breakers that each protect one circuit: kitchen sockets, bedroom sockets, lighting, the water heaters, the AC units. When something trips, which switch went down tells you most of the story before anyone picks up a phone.
UAE boards have a few local quirks worth knowing before trouble starts. Water heaters usually have their own switches, sometimes on the board and sometimes on the bathroom wall, and each split AC unit typically has a dedicated isolator. Older flats often carry a second small board for the heaters alone. Ten minutes spent flipping breakers one by one and writing what each controls on the board's door turns your next fault call from a vague description into a precise one, and shortens the electrician's paid diagnosis time accordingly.
AED ranges
Rather than publishing one rate, tamam shows what multiple verified vendors charge for wiring repair so you can pick the tier that fits the job and the budget.
Socket or switch replacement, per pointAED 150–250
New socket point as a spur on an existing circuitAED 180–350
Chandelier installation with assembly, high ceilingAED 350–600
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
What you finally pay depends on the vendor and tier you choose — all of it visible before booking.
Avoid these
Fixing nuisance trips by fitting a bigger breaker or a less sensitive RCD
Upsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
Booking tower work without checking permit rules first
Many managed buildings turn contractors away without a work permit or landlord NOC, and some restrict noisy work to weekday hours. The result is a paid visit that ends in the lobby. One message to building management before you pick a slot avoids the wasted call-out.
Treating outdoor electrics like indoor electrics
Indoor-grade junction boxes in flowerbeds, unrated extension cords feeding garden lights and balcony sockets without covers all fail the same way: moisture gets in, the RCD starts tripping, and the search for the wet joint costs more than proper IP-rated fittings would have. Outdoors, specification is the economy.
Frequently asked questions
Why does my breaker trip every time it rains or the humidity spikes?
Moisture is getting into an outdoor fitting, balcony socket, external water heater cupboard or garden joint and leaking current to earth, which the RCD correctly detects. It feels random because it follows weather, not usage. An electrician isolates circuits at the DB and tests insulation resistance to find the wet point, then re-terminates it in a properly sealed enclosure.
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
Do I have to pay for electrical repairs in my rented apartment?
Check your tenancy contract for a minor-maintenance clause; the common UAE arrangement makes tenants responsible for small repairs up to a stated amount per incident, with the landlord covering wear-and-tear and anything structural. An aging water heater leaking to earth is wear, not misuse, so document faults with photos and dates before agreeing to pay.
How do I know the electrician I am booking is actually qualified?
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Is it worth adding RCD protection to an older building's board?
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
Do you cover The Villa Project?
Yes — The Villa Project is covered across Dubai, with vendors who regularly work the area. Availability shows live in the app.