ttamamusually replies in minutes11:14
pinnedfrom AED 150–600visit length 1–3 hourslocation Al Hamidiya, Ajmanvendors verified
need wiring repair in al hamidiya — today if possible11:14✓✓
If you need electrician in Al Hamidiya, the useful question isn't who is cheapest — it's who is available, licensed, and priced transparently. tamam answers all three in one screen.11:15
typical ranges vendors quote around al hamidiya —Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250New socket point as a spur on an existing circuitAED 180–350Light fixture or ceiling fan installation, standard ceilingAED 150–35011:16
that works. who actually turns up?11:17✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:18
The tower renter: what is yours, what is the building's, what is the landlord's
In an apartment, three parties share the electrical picture. The utility owns everything up to your meter. The building owns the risers, common-area wiring and the supply into your flat. Everything after your DB is the landlord's asset, and your tenancy contract decides who pays for repairs; the common UAE convention is that minor repairs below a threshold written into the contract fall to the tenant, while anything structural or aging-related is the landlord's problem. Read that clause before you spend anything, and photograph faults so the conversation stays factual.
Towers add a layer of process. Most managed buildings in Dubai Marina, JLT, Reem Island or Al Majaz require a work permit for any contractor entering the building, often restricted to weekday daytime hours, sometimes with a requirement that the company carries insurance. For a simple socket swap this is usually waved through at the security desk; for anything involving drilling or wall chasing, the building may want the landlord's no-objection letter first. Ask your building management what they need before the electrician is standing in the lobby.
Where a handyman stops and an approved contractor begins
UAE utilities draw a firm line through every home. DEWA, SEWA, ADDC and Etihad WE own and control everything up to and including the meter; nobody you hire may touch it, and a damaged meter seal alone can trigger penalties. Beyond the meter, the rule of thumb is that like-for-like work is handyman territory while anything that changes the installation needs a contractor holding the relevant utility approval: replacing or upgrading the DB itself, adding new circuits, rewiring, increasing the connected load for a bigger AC or an EV charger, or anything the utility must inspect and reconnect.
The boundary matters for more than compliance. Home insurance can walk away from a fire claim traced to unapproved modification of the fixed installation, and villa owners feel it at resale, when a buyer's inspection flags a DB full of undocumented additions. If a vendor quotes you for a load increase or a DB replacement without mentioning utility approval or an inspection step, that is your cue to ask harder questions or find another vendor.
What you should expect to pay
Pricing for wiring repair in Al Hamidiya moves with the size of the job, the vendor tier you choose, and any parts or consumables involved. tamam shows AED ranges before you book rather than one fixed number.
Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250
New socket point as a spur on an existing circuitAED 180–350
Light fixture or ceiling fan installation, standard ceilingAED 150–350
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
Nothing is charged until you have chosen a vendor and seen their number. There are no surprise call-out fees.
Frequently asked questions
Why does my breaker trip every time it rains or the humidity spikes?
Moisture is getting into an outdoor fitting, balcony socket, external water heater cupboard or garden joint and leaking current to earth, which the RCD correctly detects. It feels random because it follows weather, not usage. An electrician isolates circuits at the DB and tests insulation resistance to find the wet point, then re-terminates it in a properly sealed enclosure.
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
My whole flat lost power but the neighbours are fine. Who do I call?
First check your own DB: if the main isolator or RCD has dropped, reset it once. If the board is fully on but the flat is dead, the fault is likely at the meter or the building's riser, which is the utility's or building management's side. Call the building's maintenance desk or the utility's fault line; a private electrician cannot legally open that part of the installation.
What is an RCD, and why does mine trip when the washing machine runs?
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
Can electricians work evenings or weekends in apartment towers?
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
Do you cover Al Hamidiya?
We cover Al Hamidiya and the surrounding Ajman communities. Message on whatsapp if you want a specific time confirmed first.
Avoid these
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Treating outdoor electrics like indoor electrics
Indoor-grade junction boxes in flowerbeds, unrated extension cords feeding garden lights and balcony sockets without covers all fail the same way: moisture gets in, the RCD starts tripping, and the search for the wet joint costs more than proper IP-rated fittings would have. Outdoors, specification is the economy.