For anyone arranging electrician around Manama Ajman, tamam removes the two annoying parts — finding someone trustworthy, and finding out the price before they arrive.
Download the appBook on WhatsAppVendors covering Manama Ajman tend to have prior jobs in the area, which matters more than it sounds — tower clearance, gate access and lift bookings are where visits usually lose time.
Coverage is reliable, and pricing tends to sit toward the value end of the range. Typical on-site time is 1–3 hours. Vendors will flag it in advance if your job looks heavier than standard.
Dead sockets, loose fittings and scorched outlets replaced.
You can book socket repair entirely over whatsapp if that is easier — describe the job, get AED ranges back, confirm.
Rather than publishing one rate, tamam shows what multiple verified vendors charge for socket repair so you can pick the tier that fits the job and the budget.
| work | guide price |
|---|---|
| Call-out with fault diagnosis (tripping breaker, dead circuit) | AED 150–250 |
| New socket point as a spur on an existing circuit | AED 180–350 |
| RCD or breaker replacement in the DB | AED 200–450 |
What you finally pay depends on the vendor and tier you choose — all of it visible before booking.
Every UAE home has a distribution board (DB), usually a grey or white panel near the entrance or in the corridor. Inside sit a main isolator, one or more RCDs (residual current devices, the wide switches with a test button) and a row of MCBs, the small breakers that each protect one circuit: kitchen sockets, bedroom sockets, lighting, the water heaters, the AC units. When something trips, which switch went down tells you most of the story before anyone picks up a phone.
UAE boards have a few local quirks worth knowing before trouble starts. Water heaters usually have their own switches, sometimes on the board and sometimes on the bathroom wall, and each split AC unit typically has a dedicated isolator. Older flats often carry a second small board for the heaters alone. Ten minutes spent flipping breakers one by one and writing what each controls on the board's door turns your next fault call from a vague description into a precise one, and shortens the electrician's paid diagnosis time accordingly.
A competent electrician can audit a one- or two-bedroom flat in a couple of hours: test every socket with a tester, press-test each RCD, check water heater elements for earth leakage before they become the next tenant's mystery trip, tighten DB terminals that loosen with thermal cycling, replace yellowed or cracked switch plates, and label the DB so the next occupant is not flipping breakers at random. In villas, add the garden circuits and the external water heater cupboards, which bake in the sun.
If you manage several units, consistency is worth more than any single cheap visit. Booking through tamam lets you rebook the same vendor across units and tenancy changeovers, so the person who labelled the DB in unit 704 is the one who answers when unit 1102 starts tripping, and the payment and job history sit in the app rather than in a folder of WhatsApp screenshots.
Hanging a light in the UAE is rarely the two-screw job it is in countries with timber joists. Apartment ceilings are typically concrete slab, sometimes with a suspended gypsum layer below it. Concrete needs a hammer drill and proper anchors; gypsum alone will hold a lightweight LED panel on toggle anchors but nothing heavier. Chandeliers and anything with real mass must be fixed through to the slab or to a support frame above the gypsum, which is why a chandelier quote includes more labour than a batten holder swap, before you even count the hour of crystal assembly some of them demand.
Ceiling fans are the case people underestimate. A fan is a moving load that works loose over time, so it needs a fan-rated mount into structure, never into gypsum alone, and its wall controller or remote receiver needs wiring correctly with the light circuit. Dimmers bring their own trap: most cheap LED downlights and drivers are not dimmable, and pairing a standard dimmer with them produces flicker, buzzing or dead lamps. Say what lamps you have when you book, and the electrician can bring a compatible trailing-edge dimmer instead of discovering the mismatch on your ceiling.
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.
Download the appBook via WhatsAppUpsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Many managed buildings turn contractors away without a work permit or landlord NOC, and some restrict noisy work to weekday hours. The result is a paid visit that ends in the lobby. One message to building management before you pick a slot avoids the wasted call-out.
Every vendor on tamam has a verified trade licence with the relevant municipality, checked insurance, and technicians who are ID-tagged in the app.
First check your own DB: if the main isolator or RCD has dropped, reset it once. If the board is fully on but the flat is dead, the fault is likely at the meter or the building's riser, which is the utility's or building management's side. Call the building's maintenance desk or the utility's fault line; a private electrician cannot legally open that part of the installation.
Not directly. The UAE supply is 220–240V, and plugging a 110V appliance in without a step-down transformer will damage it, often immediately. Small dual-voltage electronics like laptop chargers are fine with a plug adapter, but motors, kitchen appliances and anything with a heating element need a correctly rated transformer or, more sensibly, a local replacement.
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
We cover Manama Ajman and the surrounding Ajman communities. Message on whatsapp if you want a specific time confirmed first.
socket repair elsewhere in ajman
more electrician in manama ajman
other home services in manama ajman