tamam connects Internet City households and businesses with vetted electrician providers. You see the options, the AED range and the availability, then book directly.
Download the appBook on WhatsAppVendors covering Internet City tend to have prior jobs in the area, which matters more than it sounds — tower clearance, gate access and lift bookings are where visits usually lose time.
Vendor availability is steady and lead times are typically short. 1–3 hours is the usual window for socket repair; larger properties or added scope push it out.
Dead sockets, loose fittings and scorched outlets replaced.
In an apartment, three parties share the electrical picture. The utility owns everything up to your meter. The building owns the risers, common-area wiring and the supply into your flat. Everything after your DB is the landlord's asset, and your tenancy contract decides who pays for repairs; the common UAE convention is that minor repairs below a threshold written into the contract fall to the tenant, while anything structural or aging-related is the landlord's problem. Read that clause before you spend anything, and photograph faults so the conversation stays factual.
Towers add a layer of process. Most managed buildings in Dubai Marina, JLT, Reem Island or Al Majaz require a work permit for any contractor entering the building, often restricted to weekday daytime hours, sometimes with a requirement that the company carries insurance. For a simple socket swap this is usually waved through at the security desk; for anything involving drilling or wall chasing, the building may want the landlord's no-objection letter first. Ask your building management what they need before the electrician is standing in the lobby.
UAE utilities draw a firm line through every home. DEWA, SEWA, ADDC and Etihad WE own and control everything up to and including the meter; nobody you hire may touch it, and a damaged meter seal alone can trigger penalties. Beyond the meter, the rule of thumb is that like-for-like work is handyman territory while anything that changes the installation needs a contractor holding the relevant utility approval: replacing or upgrading the DB itself, adding new circuits, rewiring, increasing the connected load for a bigger AC or an EV charger, or anything the utility must inspect and reconnect.
Handyman-level work, which most tamam electrical bookings fall into, covers fault finding, socket and switch replacement, adding a socket as a spur on an existing circuit, light fixture and fan installation, water heater replacement on an existing point, and appliance connections. The technician should still be a trained electrician; handyman-level describes the regulatory weight of the job, not the skill it needs.
Hanging a light in the UAE is rarely the two-screw job it is in countries with timber joists. Apartment ceilings are typically concrete slab, sometimes with a suspended gypsum layer below it. Concrete needs a hammer drill and proper anchors; gypsum alone will hold a lightweight LED panel on toggle anchors but nothing heavier. Chandeliers and anything with real mass must be fixed through to the slab or to a support frame above the gypsum, which is why a chandelier quote includes more labour than a batten holder swap, before you even count the hour of crystal assembly some of them demand.
Preparation on your side is simple: have the fixture on site, assembled as far as the box allows, confirm ceiling height so the pro brings the right ladder or platform, and know where your DB is so the lighting circuit can be isolated. Per-point pricing means a visit that installs three fixtures costs meaningfully less per fixture than three separate visits.
You can book socket repair entirely over whatsapp if that is easier — describe the job, get AED ranges back, confirm.
The vetting happens before a vendor is listed — municipality licence, valid insurance, identifiable staff — so the comparison you make is between businesses that already cleared the bar.
There is no single correct price for socket repair — there is a range, and where you land in it depends on scope and which vendor you pick. The app shows you that range up front.
As a rough guide for socket repair: socket or switch replacement, per point around AED 150–250; new socket point as a spur on an existing circuit around AED 180–350; chandelier installation with assembly, high ceiling around AED 350–600.
What you finally pay depends on the vendor and tier you choose — all of it visible before booking.
Upsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
Many managed buildings turn contractors away without a work permit or landlord NOC, and some restrict noisy work to weekday hours. The result is a paid visit that ends in the lobby. One message to building management before you pick a slot avoids the wasted call-out.
Indoor-grade junction boxes in flowerbeds, unrated extension cords feeding garden lights and balcony sockets without covers all fail the same way: moisture gets in, the RCD starts tripping, and the search for the wet joint costs more than proper IP-rated fittings would have. Outdoors, specification is the economy.
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
Check your tenancy contract for a minor-maintenance clause; the common UAE arrangement makes tenants responsible for small repairs up to a stated amount per incident, with the landlord covering wear-and-tear and anything structural. An aging water heater leaking to earth is wear, not misuse, so document faults with photos and dates before agreeing to pay.
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
We cover Internet City and the surrounding Dubai communities. Message on whatsapp if you want a specific time confirmed first.
socket repair elsewhere in dubai
more electrician in internet city
other home services in internet city
Licensed vendors, transparent AED ranges, and the same provider again next time if you liked them.
Get the tamam appBook on WhatsApp