ttamamusually replies in minutes11:42
pinnedfrom AED 150–600visit length 1–3 hourslocation Al Yahar, Abu Dhabivendors verified
need socket repair in al yahar — today if possible11:42✓✓
electrician in Al Yahar: what it involves, what it should cost in AED, and how to book a licensed vendor who actually turns up when they said they would.11:43
typical ranges vendors quote around al yahar —Light fixture or ceiling fan installation, standard ceilingAED 150–350Chandelier installation with assembly, high ceilingAED 350–600RCD or breaker replacement in the DBAED 200–45011:44
that works. who actually turns up?11:45✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:46
What you should expect to pay
There is no single correct price for socket repair — there is a range, and where you land in it depends on scope and which vendor you pick. The app shows you that range up front.
Light fixture or ceiling fan installation, standard ceilingAED 150–350
Chandelier installation with assembly, high ceilingAED 350–600
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
Villa landscape lighting repair visitAED 250–550
Final pricing comes from the vendor option you pick in the app — you see the quotes before you commit.
The tower renter: what is yours, what is the building's, what is the landlord's
In an apartment, three parties share the electrical picture. The utility owns everything up to your meter. The building owns the risers, common-area wiring and the supply into your flat. Everything after your DB is the landlord's asset, and your tenancy contract decides who pays for repairs; the common UAE convention is that minor repairs below a threshold written into the contract fall to the tenant, while anything structural or aging-related is the landlord's problem. Read that clause before you spend anything, and photograph faults so the conversation stays factual.
Towers add a layer of process. Most managed buildings in Dubai Marina, JLT, Reem Island or Al Majaz require a work permit for any contractor entering the building, often restricted to weekday daytime hours, sometimes with a requirement that the company carries insurance. For a simple socket swap this is usually waved through at the security desk; for anything involving drilling or wall chasing, the building may want the landlord's no-objection letter first. Ask your building management what they need before the electrician is standing in the lobby.
Avoid these
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Fixing nuisance trips by fitting a bigger breaker or a less sensitive RCD
Upsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Frequently asked questions
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
My whole flat lost power but the neighbours are fine. Who do I call?
First check your own DB: if the main isolator or RCD has dropped, reset it once. If the board is fully on but the flat is dead, the fault is likely at the meter or the building's riser, which is the utility's or building management's side. Call the building's maintenance desk or the utility's fault line; a private electrician cannot legally open that part of the installation.
What is an RCD, and why does mine trip when the washing machine runs?
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
Can electricians work evenings or weekends in apartment towers?
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
Is it worth adding RCD protection to an older building's board?
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
Do you cover Al Yahar?
Yes — Al Yahar is covered across Abu Dhabi, with vendors who regularly work the area. Availability shows live in the app.