tamam › home › handyman › shelf installation in one central
handyman in One Central: what it involves, what it should cost in AED, and how to book a licensed vendor who actually turns up when they said they would.
Vendors covering One Central tend to have prior jobs in the area, which matters more than it sounds — tower clearance, gate access and lift bookings are where visits usually lose time.
Demand here is high, so slots move quickly — booking a day ahead usually gets you the window you actually want. Most shelf installation jobs in this kind of area take around 1–3 hours, though access and scope shift that.
Floating and bracketed shelving anchored for real loads.
Next comes scope confirmation. The technician restates what will be done, what materials are needed, and whether anything on your list is actually outside a handyman's lane, wiring a new power point, for example, belongs to a licensed electrician under DEWA and municipality rules, and a good handyman says so rather than improvising. Then protection goes down: drop sheets under drilling points, and ideally a vacuum or dust catcher held at the drill hole, because red block dust stains light grout and carpet.
The work itself follows the sequence agreed, and the visit ends with a walkthrough in reverse: every fixing gets a firm pull test, levels go back on the shelves and frames, offcuts and packaging leave with the technician, and you check each item against your original list. Most call-outs in the UAE carry a minimum charge, typically AED 100-200, which usually covers arrival and the first block of labour. That minimum is exactly why batching several small jobs into one visit is the single best money decision in this trade, more on that below.
Furniture assembly looks unskilled until you have watched someone do it badly. The core skill is torque discipline: most flat-pack furniture is MDF or particleboard, and the cam-lock and confirmat fittings that hold it together strip the moment they are overtightened. A pro runs a drill-driver with the clutch set low for speed, then finishes every fitting by hand. The second skill is sequence, reading the exploded diagram once, sorting fittings into trays, and building sub-assemblies flat on the floor protected by the packaging cardboard rather than on bare tile.
Realistic times matter for planning your visit: a standard double bed frame takes 60-90 minutes; a chest of drawers with runners, about an hour; a large multi-door wardrobe is a two-to-four-hour job and genuinely needs two people to lift the carcass upright without racking it out of square. If a vendor quotes a six-door sliding wardrobe as a one-hour solo job, the quote is wrong and the wardrobe will show it.
You can read a technician's standards from their kit before they touch a wall. The baseline for UAE work is a cordless hammer drill with masonry, wood and metal bits; a drill-driver with a clutch for flat-pack work; a cross-line laser and a traditional spirit level; a metal-stud detector and a strong magnet; and an anchor box that covers the local reality, nylon plugs in several sizes, plasterboard self-drives, toggles, cavity fixings and at least a few chemical-anchor options for hollow block.
The finishing and protection layer matters just as much: drop sheets, masking tape, a handheld vacuum or dust-catch attachment, sanitary silicone with a proper gun and tooling kit, hardwood dowels and wood glue for stripped hinges, and a step platform or ladder rated for ceiling work. What the technician usually does not carry is your specific hardware: TV brackets, curtain rails, mirrors and shelves are normally customer-supplied unless you agree otherwise in the quote, so confirm who buys what before the visit, not at your doorstep.
See who is available in One Central right now, with prices before you commit.
Every vendor on tamam has a verified trade licence with the relevant municipality, checked insurance, and technicians who are ID-tagged in the app.
message what you need on whatsapp if the app isn't handy
a coordinator matches One Central vendors to the job
you approve the range before anyone is dispatched
arrival time confirmed in writing
pay in-app or arrange it through support
shelf installation generally falls in the AED 100–500 band. Comparing several verified vendors on the same job description is what stops you overpaying.
What you finally pay depends on the vendor and tier you choose — all of it visible before booking.
AED 100–500
Dubai's tower-heavy stock means the building, not the emirate, sets most of the rules. Marina, JLT, Downtown and Business Bay towers commonly require a work permit or NOC from building management before a technician drills anything, plus contractor access through the service lift during set hours, often 9am to 6pm on weekdays only. Factor the permit lead time into your booking, and remember that post-2005 towers are heavy on gypsum partitions, so brief heavy-mounting jobs accordingly. Anything touching electrical circuits or water supply beyond simple fixtures crosses into DEWA and Dubai Municipality licensed-trade territory.
Tools, yes, always: drills, levels, anchors and consumables like screws and basic plugs are part of the service. Specific hardware is different: TV brackets, curtain rails, mirrors, shelves and replacement hinges are normally customer-supplied unless the quote says otherwise. Confirm the split when you accept the quote so nobody is standing in a hardware store mid-visit.
Only at fixture level: swapping a light fitting, changing a tap washer, fitting an appliance. New wiring, new power points, anything at the distribution board, or work on supply pipework needs a licensed electrician or plumber under DEWA, SEWA or ADDC and municipality rules. A good handyman will tell you where that line is rather than crossing it.
Yes, if it is fixed correctly. Light frames go on plasterboard anchors, but a heavy mirror needs to land on the metal studs behind the board or use rated cavity fixings across multiple points. If the technician cannot tell you which method they are using and why, pause the drilling.
In many Dubai and Abu Dhabi towers and masterplanned communities, yes: management requires a work permit or NOC, and often restricts noisy work to set weekday hours. Villas and most older buildings need nothing formal beyond a word with the watchman. Check with your building before booking, because a technician turned away at security still counts as a visit.
Most vendors work Saturdays and many work Sundays, which suits commuting households, but tower rules can override this: plenty of buildings ban drilling on weekends or after 6pm. Quiet jobs, assembly, silicone, door adjustment, are usually fine any day. Check your building's noisy-work hours before booking a weekend slot.
We cover One Central and the surrounding Dubai communities. Message on whatsapp if you want a specific time confirmed first.
Every visit carries the call-out minimum, so three single-job bookings can cost more than one half-day visit that clears ten jobs. Keep a running list on your phone and book when it reaches three or four items. Vendors also quote batched work more competitively because their travel time is spread across more billable tasks.
New silicone does not bond to old silicone, and mould trapped underneath grows straight through the fresh bead. If the technician is not spending most of the job on removal and drying, the reseal will fail within months. Ask to see the joint clean and dry before the new bead goes in.
In permit-controlled towers, a technician stopped at security is a wasted visit that you may still be charged for. Five minutes with building management before booking, asking about NOCs, service-lift rules and drilling hours, protects both your slot and your deposit with the building.