tamam covers Town Square for car polishing the same way it covers every UAE community: multiple vetted vendors, AED ranges you can see up front, and booking that takes a couple of taps.
Download the appBook on WhatsAppTown Square sits within Dubai, and local conditions do influence car polishing: access procedures, building rules and seasonal demand all shift how a booking should be planned.
Vendor availability is steady and lead times are typically short. Typical on-site time is 2–5 hours. Vendors will flag it in advance if your job looks heavier than standard.
Swirls and scratches machined out in stages.
Free to download, free to browse. You only pay when you book a job.
Get the tamam appMessage on WhatsAppNot everything fits neatly into an app form. For anything custom in Town Square, whatsapp a coordinator and it gets handled manually.
Watch what happens before any machine is switched on. A competent technician spends ten to fifteen minutes walking the car with a handheld inspection light, because defects invisible under a shaded canopy jump out under a focused LED beam. They are cataloguing the damage: swirl marks (the spiderweb pattern in sunlight, almost always from dry dusting or bad wash technique), random isolated deeper scratches, water spot etching from sprinkler overspray, and bird dropping marks baked in under summer heat.
The walkaround should end with a conversation, not a handshake: which defects will come out fully, which will only be reduced (anything deep enough to catch a fingernail is usually beyond polishing alone), and how many stages the job needs. If you are booking through tamam, ask for exactly this detail over the WhatsApp coordination before confirming — a vendor who can describe your paint from your photos is quoting the job, not guessing at it.
No polishing pad should ever meet a dirty panel. UAE dust is fine crystalline silica — effectively airborne sandpaper — and any grit trapped under a spinning pad will carve fresh scratches faster than the compound can remove old ones. So the job starts with a thorough wash: a pre-rinse or snow foam to lift loose dust, then a two-bucket hand wash with a proper mitt, working top down so the dirtiest water never travels upward.
Done properly this stage takes 60–90 minutes, and it is non-negotiable: a quote promising a full polish in two hours flat has compressed or skipped decontamination. The final prep step is taping — rubber trim, textured plastics, badges and panel gaps get masked, because compound stains porous plastic white and a pad edge catching a badge at speed damages both.
The restoration process is miniature paint correction. The technician masks the surrounding paint, then wet-sands the lens through progressively finer grits — typically 800 to 1500 to 3000 — removing the dead UV layer entirely. At this point the lens looks uniformly frosted, which alarms customers who have not seen the process before. Machine polishing with a plastic-specific compound then brings it back to full clarity. The whole job runs 30–60 minutes for the pair and typically costs AED 150–300 in this market.
The step separating a lasting job from a six-month one is re-sealing. Sanding removed the factory UV protection, so bare polished polycarbonate yellows again fast under Gulf sun. A proper finish applies a UV-resistant sealant or a sprayed lens clear coat — ask specifically what goes on and how long it should hold. The answer tells you whether you are buying a restoration or a temporary shine before your inspection date.
Trade licences are checked against the issuing municipality, not self-declared, and insurance has to be current for a vendor to stay listed.
Rather than publishing one rate, tamam shows what multiple verified vendors charge for paint correction so you can pick the tier that fits the job and the budget.
| service | typical range |
|---|---|
| Single-stage machine polish, sedan | AED 200–400 |
| Two-stage paint correction, sedan | AED 400–700 |
| Headlight restoration with UV sealant, pair | AED 150–300 |
Parts and consumables, where they apply, are quoted separately and approved by you first.
Clear coat is a budget that runs out. A car that gets aggressively machine-polished every few months will eventually strike through on edges and high points, and the only fix at that point is a respray. Correct properly once, then protect and wash correctly so you do not need to cut again for a year or more.
Standard compound on a matte wrap creates a permanent glossy scar; standard cutting pressure on a soft respray burns through; polishing a ceramic-coated car strips the coating you paid for. Surface type determines process, and the vendor can only plan for what they know about.
Sanding and polishing a hazed lens removes the factory UV coating along with the yellowing. Left bare, polycarbonate re-hazes under Gulf sun within months, sometimes before your next inspection. Confirm a UV sealant or lens clear coat is part of the job, not an optional extra you discover afterwards.
Polishing is abrasive: it removes a thin layer of clear coat to physically eliminate swirls and light scratches. Waxing is additive: it lays a protective, glossy layer on top of the paint without fixing anything underneath. A proper job usually does both, in that order — correct first, protect second.
Done correctly, it removes only a few microns of clear coat and leaves the paint healthier-looking and easier to protect. The risk comes from repeated aggressive cutting, rotary work near edges, or polishing paint that is already thin — which is why depth readings before heavy correction matter. Ask your vendor how much cut the job needs and why.
A single-stage polish on a sedan takes roughly 3–4 hours including the wash and decontamination; a two-stage correction runs 5–7 hours; a three-stage job on an SUV can fill a working day. Quotes promising a full machine polish in under two hours are compressing the preparation stages, and the finish will show it within a few washes.
No. Polishing creates gloss by levelling the surface, which permanently ruins the light-scattering texture that makes matte look matte. A glossy patch on a matte panel cannot be reversed without re-wrapping or repainting. Matte finishes need dedicated cleaning and sealant products, so always tell the vendor the car is matte before booking anything.
Inspect the car in direct sunlight or with a torch held at a low angle to the bonnet, roof and doors, looking for hologram ribbons and remaining swirls. Check trim for white compound staining, panel gaps for dried polish dust, and edges for any burn marks. Two minutes of inspection at handover prevents most disputes later.
Town Square is within our Dubai coverage. Open the app to see which vendors have slots near you today.
paint correction elsewhere in dubai
more car polishing in town square
other car services in town square