tamam connects Corniche households and businesses with vetted electrician providers. You see the options, the AED range and the availability, then book directly.
Download the appBook on WhatsAppThe character of Corniche — primarily residential, so most bookings are villa or apartment work and timing follows family routines — determines what a good electrician visit looks like here, from the equipment brought to the slot that gets chosen.
Vendor availability is steady and lead times are typically short. Most light installation jobs in this kind of area take around 1–3 hours, though access and scope shift that.
Ceiling lights, chandeliers and spots fitted safely.
There is one safe DIY step: unplug everything on the affected circuit, reset the breaker, and reintroduce appliances one at a time. If the breaker holds until a specific device goes back in, you have found your culprit. If it snaps back instantly with nothing plugged in, or you notice a burning smell or a breaker that feels warm, stop resetting it and book a professional. Repeatedly forcing a breaker that wants to trip is how melted DB buswork happens.
UAE boards have a few local quirks worth knowing before trouble starts. Water heaters usually have their own switches, sometimes on the board and sometimes on the bathroom wall, and each split AC unit typically has a dedicated isolator. Older flats often carry a second small board for the heaters alone. Ten minutes spent flipping breakers one by one and writing what each controls on the board's door turns your next fault call from a vague description into a precise one, and shortens the electrician's paid diagnosis time accordingly.
UAE utilities draw a firm line through every home. DEWA, SEWA, ADDC and Etihad WE own and control everything up to and including the meter; nobody you hire may touch it, and a damaged meter seal alone can trigger penalties. Beyond the meter, the rule of thumb is that like-for-like work is handyman territory while anything that changes the installation needs a contractor holding the relevant utility approval: replacing or upgrading the DB itself, adding new circuits, rewiring, increasing the connected load for a bigger AC or an EV charger, or anything the utility must inspect and reconnect.
Handyman-level work, which most tamam electrical bookings fall into, covers fault finding, socket and switch replacement, adding a socket as a spur on an existing circuit, light fixture and fan installation, water heater replacement on an existing point, and appliance connections. The technician should still be a trained electrician; handyman-level describes the regulatory weight of the job, not the skill it needs.
Extension-lead sprawl is how most UAE homes signal that they need more sockets: a four-way behind the TV feeding another four-way, a kettle and microwave sharing one adapter. Adding a proper socket is a modest job when it can spur off an existing nearby point, and a bigger one when it needs a new run back to the DB. The finish drives the price as much as the electrics: surface trunking is quick and visible; chasing cable into blockwork and replastering is neat and slower; in towers with gypsum partition walls, fishing cable inside the wall is often the tidy middle path.
Renters have one extra step: chasing walls or adding circuits alters the landlord's asset, so it needs written permission, and many landlords will only agree to surface trunking that can be removed at handover. Get the agreement on record in the same email chain as the quote and nobody argues about it at move-out.
You can book light installation entirely over whatsapp if that is easier — describe the job, get AED ranges back, confirm.
Every vendor on tamam has a verified trade licence with the relevant municipality, checked insurance, and technicians who are ID-tagged in the app.
The honest answer on cost is a range, not a figure. For light installation the typical band is AED 150–600, and you see each vendor's position in it before committing.
As a rough guide for light installation: socket or switch replacement, per point around AED 150–250; new socket point as a spur on an existing circuit around AED 180–350; chandelier installation with assembly, high ceiling around AED 350–600.
Parts and consumables, where they apply, are quoted separately and approved by you first.
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Many managed buildings turn contractors away without a work permit or landlord NOC, and some restrict noisy work to weekday hours. The result is a paid visit that ends in the lobby. One message to building management before you pick a slot avoids the wasted call-out.
Check your tenancy contract for a minor-maintenance clause; the common UAE arrangement makes tenants responsible for small repairs up to a stated amount per incident, with the landlord covering wear-and-tear and anything structural. An aging water heater leaking to earth is wear, not misuse, so document faults with photos and dates before agreeing to pay.
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
We cover Corniche and the surrounding Abu Dhabi communities. Message on whatsapp if you want a specific time confirmed first.
light installation elsewhere in abu dhabi
more electrician in corniche
other home services in corniche
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.
Get the tamam appWhatsApp us