the going rate · dubai
ranges are typical · live quotes in chat
If you need handyman in Dubai Internet City, the useful question isn't who is cheapest — it's who is available, licensed, and priced transparently. tamam answers all three in one screen.
one meter · three job sizes
In Dubai Internet City, the difference between a smooth handyman visit and a wasted afternoon usually comes down to whether the vendor has worked the area before.
Vendor availability is steady and lead times are typically short. Budget roughly 1–3 hours on site for handyman, plus a little for access if the building has a lift protocol.
On block or concrete, the job is straightforward: a hammer drill with a 6 or 8 millimetre masonry bit, nylon plugs matched to the screw, and the bracket pulls up rock solid. Expect 45-60 minutes for a fixed or tilting mount up to 65 inches, including unboxing, levelling and cable tidy-up. On gypsum, the calculus changes. A fixed mount for a mid-size TV can go onto heavy-duty toggle anchors spread across the plate, but a full-motion articulating arm concentrates leverage onto a few fixing points, and on gypsum that demands hitting at least two metal studs or, better, fitting a plywood backing board first. A technician who proposes screwing a swing arm straight into plasterboard with plastic plugs is telling you they have not done this long.
Good workmanship shows in the details you can check yourself: the TV sits level (put a spirit-level app on the top edge), cables run through a trunking channel or in-wall conduit rather than dangling, the mount's locking screws are fitted so the panel cannot be lifted off by a curious child, and the technician does a firm downward pull on the bracket before hanging the screen. Budget 60-90 minutes if cable concealment or a soundbar is involved.
UAE doors misbehave for two local reasons. First, humidity: timber doors swell through the humid months, roughly June to September on the coast, and a door that fit perfectly in February starts scraping its frame in August. Second, air pressure: a closed apartment with the AC running sits at a slightly different pressure to the corridor, which is why doors slam themselves or refuse to close that final centimetre. Diagnosis comes before tools: a pro closes the door slowly, watches where the gap tightens, and checks the hinge screws before assuming the door needs planing.
Nine times out of ten the fix is at the hinge. Years of use strip the top hinge screws out of the frame, letting the door drop and bind at the latch corner. The repair sequence is: remove the stripped screws, plug the holes with glued hardwood dowels or fit longer screws that reach the wall structure behind the frame, and re-hang. If the door still binds after the hinges are true, then and only then does the plane or belt sander come out, taken to the bottom or latch edge in light passes, with the bare timber resealed afterwards so it does not just swell again next summer. Latch problems usually need nothing more than moving the strike plate a couple of millimetres.
Every job in this guide has an objective pass test, and the time to apply it is while the technician is still in your home. Pull firmly on every bracket, rail and mount, a proper fixing does not move at all, and a professional will do this pull test in front of you without being asked. Sight along rails and frames or ask for the laser to be held up one last time. Open and close every adjusted door at normal speed. Run a finger along silicone lines to check the edges are bonded (gently, and only if the bead has skinned). Count the holes: there should be exactly as many as there are fixings, and any abandoned holes should have been filled before the tools were packed.
Finally, keep the relationship. Handyman work is the most repeat-heavy trade in home services, there is always a next list, and a technician who already knows your wall types and building rules is measurably faster on visit two. If the work passed your walkthrough, rebook the same vendor next time; tamam keeps the vendor attached to your booking history so the same team can come back, and you can coordinate the details over whatsapp rather than re-explaining your building from scratch.
The honest answer on cost is a range, not a figure. For handyman the typical band is AED 100–500, and you see each vendor's position in it before committing.
Licensed vendors, transparent AED ranges, and the same provider again next time if you liked them.
Verification is not a badge on a page — licences are confirmed with the issuing authority, insurance is checked, and every technician is identifiable in-app before they arrive.
Dubai's tower-heavy stock means the building, not the emirate, sets most of the rules. Marina, JLT, Downtown and Business Bay towers commonly require a work permit or NOC from building management before a technician drills anything, plus contractor access through the service lift during set hours, often 9am to 6pm on weekdays only. Factor the permit lead time into your booking, and remember that post-2005 towers are heavy on gypsum partitions, so brief heavy-mounting jobs accordingly. Anything touching electrical circuits or water supply beyond simple fixtures crosses into DEWA and Dubai Municipality licensed-trade territory.
New silicone does not bond to old silicone, and mould trapped underneath grows straight through the fresh bead. If the technician is not spending most of the job on removal and drying, the reseal will fail within months. Ask to see the joint clean and dry before the new bead goes in.
In permit-controlled towers, a technician stopped at security is a wasted visit that you may still be charged for. Five minutes with building management before booking, asking about NOCs, service-lift rules and drilling hours, protects both your slot and your deposit with the building.
The cheapest quote often prices a different job: silicone over silicone, plugs instead of proper anchors, no anti-tip strap on the wardrobe. When quotes differ widely, ask each vendor how they will do the job. The one who mentions wall type, anchors and cure times without prompting is usually the one worth paying.
Tools, yes, always: drills, levels, anchors and consumables like screws and basic plugs are part of the service. Specific hardware is different: TV brackets, curtain rails, mirrors, shelves and replacement hinges are normally customer-supplied unless the quote says otherwise. Confirm the split when you accept the quote so nobody is standing in a hardware store mid-visit.
In many Dubai and Abu Dhabi towers and masterplanned communities, yes: management requires a work permit or NOC, and often restricts noisy work to set weekday hours. Villas and most older buildings need nothing formal beyond a word with the watchman. Check with your building before booking, because a technician turned away at security still counts as a visit.
Significantly. The call-out minimum, typically AED 100-200, is charged per visit, so five separate bookings pay that floor five times. A batched list turns the same jobs into one half-day visit around AED 300-500, and vendors quote batched work more keenly because the travel is amortised.
In Dubai, Sharjah and Abu Dhabi, next-day slots are usually realistic and same-day is possible for simple jobs. In RAK, Fujairah and UAQ, where many teams travel from other emirates, one to two days ahead is safer. Move-in season, September and the weeks around school start, tightens availability everywhere.
Most vendors work Saturdays and many work Sundays, which suits commuting households, but tower rules can override this: plenty of buildings ban drilling on weekends or after 6pm. Quiet jobs, assembly, silicone, door adjustment, are usually fine any day. Check your building's noisy-work hours before booking a weekend slot.
We cover Dubai Internet City and the surrounding Dubai communities. Message on whatsapp if you want a specific time confirmed first.
Licensed vendors, transparent AED ranges, and the same provider again next time if you liked them.