the going rate · dubai
ranges are typical · live quotes in chat
For anyone arranging handyman around Karama, tamam removes the two annoying parts — finding someone trustworthy, and finding out the price before they arrive.
one meter · three job sizes
Anyone who has arranged handyman in Karama knows the friction isn't the work itself — it's coordination. Vendors familiar with the area cut that down considerably.
Vendor availability is steady and lead times are typically short. Budget roughly 1–3 hours on site for furniture assembly, plus a little for access if the building has a lift protocol.
Flat-pack builds, wardrobes, beds and office desks assembled properly.
Most TV-mounting advice online is written for North American timber-frame houses. UAE apartments and villas are built differently: exterior and structural walls are concrete block or poured concrete finished with plaster, while many internal partitions, especially in towers built after roughly 2005, are gypsum board on light-gauge metal studs. A timber stud finder is useless here. The professional method is a knock test first (block sounds dead, gypsum sounds hollow), then a magnet or metal-stud detector to map the studs at their usual 400 or 600 millimetre spacing.
On block or concrete, the job is straightforward: a hammer drill with a 6 or 8 millimetre masonry bit, nylon plugs matched to the screw, and the bracket pulls up rock solid. Expect 45-60 minutes for a fixed or tilting mount up to 65 inches, including unboxing, levelling and cable tidy-up. On gypsum, the calculus changes. A fixed mount for a mid-size TV can go onto heavy-duty toggle anchors spread across the plate, but a full-motion articulating arm concentrates leverage onto a few fixing points, and on gypsum that demands hitting at least two metal studs or, better, fitting a plywood backing board first. A technician who proposes screwing a swing arm straight into plasterboard with plastic plugs is telling you they have not done this long.
Furniture assembly looks unskilled until you have watched someone do it badly. The core skill is torque discipline: most flat-pack furniture is MDF or particleboard, and the cam-lock and confirmat fittings that hold it together strip the moment they are overtightened. A pro runs a drill-driver with the clutch set low for speed, then finishes every fitting by hand. The second skill is sequence, reading the exploded diagram once, sorting fittings into trays, and building sub-assemblies flat on the floor protected by the packaging cardboard rather than on bare tile.
The non-negotiable finish item is anti-tip anchoring. Wardrobes, bookcases and tall drawer units come with wall straps for a reason, and in a household with children they are not optional. On block walls this is a two-minute plug-and-screw; on gypsum it means finding a stud or using a toggle. A technician who leaves a two-metre wardrobe freestanding on tile, in a country where almost every floor is hard tile, has skipped the most important step of the job.
The surface then has to be genuinely dry, not towel-dry but dry-dry, which in a family bathroom means the shower is out of use for a few hours before the work, worth knowing when you schedule the visit. The pro then masks both sides of the joint with tape, guns a sanitary-grade anti-fungal silicone (not general-purpose acrylic, which is cheaper and fails fast in wet areas), tools the bead smooth in one pass, and pulls the tape while the bead is wet, leaving those crisp straight edges that separate professional work from a DIY afternoon.
Then comes the part no one budgets for: cure time. Sanitary silicone needs roughly 24 hours before the shower runs again; using it the same evening washes out the surface skin and the bead fails early. A full shower enclosure reseal is 60-90 minutes of work plus that day of patience. Quality check a week later: the bead is uniform width, bonded on both edges with no lifting corners, and water sheets off it rather than creeping underneath.
Vendors are licence-checked and insurance-verified before they take a single booking, and customer ratings stay attached to their profile afterwards.
Expect AED 100–500 as the working range for furniture assembly in Karama. What moves it: job size, access difficulty, materials, and whether you want the value or premium tier.
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.
Dubai's tower-heavy stock means the building, not the emirate, sets most of the rules. Marina, JLT, Downtown and Business Bay towers commonly require a work permit or NOC from building management before a technician drills anything, plus contractor access through the service lift during set hours, often 9am to 6pm on weekdays only. Factor the permit lead time into your booking, and remember that post-2005 towers are heavy on gypsum partitions, so brief heavy-mounting jobs accordingly. Anything touching electrical circuits or water supply beyond simple fixtures crosses into DEWA and Dubai Municipality licensed-trade territory.
Tools, yes, always: drills, levels, anchors and consumables like screws and basic plugs are part of the service. Specific hardware is different: TV brackets, curtain rails, mirrors, shelves and replacement hinges are normally customer-supplied unless the quote says otherwise. Confirm the split when you accept the quote so nobody is standing in a hardware store mid-visit.
Only at fixture level: swapping a light fitting, changing a tap washer, fitting an appliance. New wiring, new power points, anything at the distribution board, or work on supply pipework needs a licensed electrician or plumber under DEWA, SEWA or ADDC and municipality rules. A good handyman will tell you where that line is rather than crossing it.
Yes, if it is fixed correctly. Light frames go on plasterboard anchors, but a heavy mirror needs to land on the metal studs behind the board or use rated cavity fixings across multiple points. If the technician cannot tell you which method they are using and why, pause the drilling.
In many Dubai and Abu Dhabi towers and masterplanned communities, yes: management requires a work permit or NOC, and often restricts noisy work to set weekday hours. Villas and most older buildings need nothing formal beyond a word with the watchman. Check with your building before booking, because a technician turned away at security still counts as a visit.
They can, but often should not, yet. Genuine construction defects belong on the developer's snag list inside the defects liability period, usually twelve months, and fixing them privately can weaken your claim. Document defects with the developer first, then use a handyman for everything the developer never owed you: mounting, rails, assembly and the move-in list.
Karama is within our Dubai coverage. Open the app to see which vendors have slots near you today.
New silicone does not bond to old silicone, and mould trapped underneath grows straight through the fresh bead. If the technician is not spending most of the job on removal and drying, the reseal will fail within months. Ask to see the joint clean and dry before the new bead goes in.
Cracked tiles, failed grout and misaligned kitchen units in a new handover are usually the developer's obligation during the defects liability period. Paying a handyman to fix them both costs you money and can undermine the official snag claim. Document and report first; hire for the jobs the developer never owed you.
The cheapest quote often prices a different job: silicone over silicone, plugs instead of proper anchors, no anti-tip strap on the wardrobe. When quotes differ widely, ask each vendor how they will do the job. The one who mentions wall type, anchors and cure times without prompting is usually the one worth paying.
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.