Residents across Arjan book car detailing through tamam because the model is simple — licensed vendors, transparent pricing, in-app tracking, and the same provider again next time if you liked them.
What makes Arjan specific for car detailing is a mix of housing type and access: primarily residential, so most bookings are villa or apartment work and timing follows family routines, with the practical constraints that come with it.
Vendor availability is steady and lead times are typically short. Typical on-site time is 3–8 hours. Vendors will flag it in advance if your job looks heavier than standard.
Inside and out, corrected and protected.
Expect AED 300–2500 as the working range for full car detailing in Arjan. What moves it: job size, access difficulty, materials, and whether you want the value or premium tier.
| job | typical AED |
|---|---|
| Single-stage machine polish / gloss enhancement | AED 500–1,000 |
| Ceramic coating including prep and correction | AED 1,000–2,500 |
| Partial-front PPF (bumper and bonnet leading edge) | AED 1,200–2,500 |
Final pricing comes from the vendor option you pick in the app — you see the quotes before you commit.
A serious detailer does not quote a paint correction from a photo. The first diagnostic is a paint depth gauge — a small ultrasonic or magnetic device pressed against each panel that reads total paint thickness in microns. Factory paint typically reads 100–160 microns. A panel reading 250 microns has been resprayed; a panel reading 80 has probably been machine-polished hard before and has little clearcoat left to work with. Correcting paint means removing clearcoat, so knowing how much remains is the difference between a safe polish and striking through to the colour coat.
Finally, they will inspect under proper light. Swirls, buffer trails from a previous bad polish, water-spot etching and bird-dropping etching all look different under an inspection lamp, and each needs a different fix. Water spotting deserves a special mention here: sprinkler overspray and mineral-heavy washing water leave alkaline deposits that, baked at 70-plus degrees, etch physical craters into clearcoat within days. If a detailer points these out during the walkaround rather than discovering them mid-job, you are dealing with someone who has priced the work honestly.
Paint correction is controlled abrasion. A machine polisher works a pad and an abrasive compound across the clearcoat, levelling the surface down to the depth of the deepest defect being removed. A swirl mark is a valley in the clearcoat; the machine removes the surrounding peaks until the surface is uniform again and light reflects cleanly. This is why correction is finite: each pass spends clearcoat you cannot get back, and why the depth-gauge readings from the walkaround matter so much.
A useful acceptance test at handover: ask to see the finished paint under the detailer's inspection lamp, not just in flattering daylight, and check the panel edges. Machine work concentrates heat and cut at edges and creases, so clean, un-burned edges are the signature of careful work. Holograms — faint buffer trails visible under direct light — mean the final refining pass was rushed.
A clean engine bay makes leaks visible, keeps connectors and labels readable, and photographs well when you sell. But the horror stories are real: a pressure washer aimed into a modern engine bay can force water past connector seals, into the alternator, or into a coil pack, and the misfire may only show up days later as corrosion sets in. The professional method is low pressure or none at all — degreaser, agitation with brushes, a gentle rinse or steam, and compressed air to dry — with the battery terminals, fuse box, alternator, intake inlet and any exposed ECU covered before a drop of anything is sprayed.
If a mobile detailer proposes to pressure-wash your engine bay in your building's car park, decline. Beyond the electrical risk, most Dubai and Abu Dhabi tower car parks prohibit runoff-producing work, and degreaser runoff is exactly what building management fines residents for. A steam-based bay clean, or doing that one item at a workshop, sidesteps both problems.
You can book full car detailing entirely over whatsapp if that is easier — describe the job, get AED ranges back, confirm.
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.
Get the tamam appBook on WhatsAppEvery technician shows in the app with a name and photo before arrival, and the business behind them has cleared licence and insurance checks.
A coating is transparent and permanent enough to be annoying: it seals in every swirl and etch mark beneath it. The suspiciously cheap coating deals almost always skip decontamination and polishing, which is precisely where the labour cost lives. Pay for the prep or skip the coating.
Products behave differently at 70 degrees: soap flash-dries into streaks, polish gums up, coatings cure before they level, and cold water on hot glass and paint adds thermal shock. Morning slots, shade or basement parking are not comfort preferences — they change the quality of the result.
Water driven past connector seals into coils, the alternator or fuse boxes causes faults that surface days later as corrosion develops, which is why the damage rarely gets connected to the wash. Bays need degreaser, brushes, covered electronics and low pressure or steam — a job for someone who has done it a few hundred times.
Realistically two to five years for a professionally applied coating, depending on the product, the quality of prep underneath it, and whether the car gets regular pH-neutral washes. Claims of seven to ten years come from milder climates and lab conditions. The first sign of a dying coating is water no longer beading or sheeting off cleanly.
Not pointless, but short-lived. Carnauba-based waxes soften at temperatures a UAE bonnet exceeds daily in summer, so expect four to eight weeks of protection rather than the months you would get in Europe. On a garaged car, or as a cheap top-up over an existing coating, wax still has a role.
Same mechanism, different ambition. Both remove a controlled amount of clearcoat with abrasives; a polish or enhancement uses one fine stage to boost gloss and clear light swirls, while a correction uses two or more stages, starting with heavier compounds, to remove deeper scratches and etching. Correction takes more hours and more clearcoat, which is why it costs more.
Usually yes, because brush-wash swirls are shallow and live entirely in the clearcoat. A single-stage polish clears most of them; heavier wash damage needs two stages. The catch is that returning to the same automatic wash reinstalls them within months, so pair the correction with a change in wash habits or the money is wasted.
Done properly, no — done with an open pressure washer, possibly. The professional method covers the battery, alternator, fuse box and air intake, uses degreaser with brushes and only low-pressure water or steam, and works on a cool engine. Water forced into connectors can cause misfires that appear days later, which is why method matters more than products here.
Yes — Arjan is covered across Dubai, with vendors who regularly work the area. Availability shows live in the app.
full car detailing elsewhere in dubai
more car detailing in arjan
other car services in arjan
Two ways in: the app for comparison and tracking, whatsapp if you would rather just talk to someone.
Get the tamam appBook on WhatsApp