ttamamusually replies in minutes11:21
pinnedprice band AED 300–2500duration 3–8 hourscovers Riyadh Cityemirate Abu Dhabi
need engine bay cleaning in riyadh city — today if possible11:21✓✓
Arranging car detailing in Riyadh City through tamam takes minutes: set the address, compare vendors and their AED ranges, choose the slot, pay in-app.11:22
typical ranges vendors quote around riyadh city —Full interior and exterior detail (no machine polish)AED 300–700Single-stage machine polish / gloss enhancementAED 500–1,000Partial-front PPF (bumper and bonnet leading edge)AED 1,200–2,50011:23
that works. who actually turns up?11:24✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:25
What you should expect to pay
Rather than publishing one rate, tamam shows what multiple verified vendors charge for engine bay cleaning so you can pick the tier that fits the job and the budget.
Full interior and exterior detail (no machine polish)AED 300–700
Single-stage machine polish / gloss enhancementAED 500–1,000
Partial-front PPF (bumper and bonnet leading edge)AED 1,200–2,500
Interior deep clean with leather treatmentAED 300–800
Engine bay detail (as an add-on)AED 200–450
Treat these as guide bands. The vendor you select confirms the exact price in-app before the job begins.
The walkaround: what a good detailer checks before quoting
The second check is contamination. The detailer runs a hand — often inside a thin plastic bag, which amplifies texture — across the paint. Paint that feels gritty rather than glass-smooth is carrying bonded contamination: industrial fallout, brake dust particles, tar, and in the UAE, mineral deposits from hard water and the occasional cement overspray from the construction site next door. None of that comes off in a wash, and polishing over it drags the particles around, so it dictates a decontamination stage before any machine work.
Finally, they will inspect under proper light. Swirls, buffer trails from a previous bad polish, water-spot etching and bird-dropping etching all look different under an inspection lamp, and each needs a different fix. Water spotting deserves a special mention here: sprinkler overspray and mineral-heavy washing water leave alkaline deposits that, baked at 70-plus degrees, etch physical craters into clearcoat within days. If a detailer points these out during the walkaround rather than discovering them mid-job, you are dealing with someone who has priced the work honestly.
Detailing to sell: the resale photo set that changes offers
The economics usually favour a mid-range job rather than a maximal one. A full detail with a single-stage polish, interior deep clean and engine bay tidy sits comfortably inside AED 700–1,500 for most cars and addresses everything a buyer touches during a viewing: paint gloss, a clean cabin that smells neutral, and an engine bay that suggests maintenance rather than neglect. A full two-stage correction and ceramic coating rarely returns its cost on an eight-year-old daily driver, though mentioning an existing coating or PPF with receipts genuinely helps on newer cars.
One honest note: detailing prepares a car for inspection, it does not beat one. Any serious buyer will run a paint depth gauge exactly as described earlier, and a respray hides from the eye but not from the meter. Present the car clean and corrected, keep your service records, and if you want to know what the buyer's inspector will find before they do, book a pre-sale inspection alongside the detail — both are bookable as separate services through tamam, and doing them in that order means the detailer can fix what the inspection flags.
What goes wrong
Dry-wiping dust off the paint
UAE dust is largely silica, harder than clearcoat, and dragging it with a dry cloth or duster sands the surface. It is the single biggest source of the swirl marks people later pay hundreds of dirhams to polish out. Dust either gets rinsed off with water and lubrication or left alone until it can be.
Judging vendors on the handover shine
Fresh dressing and a wet-look finish flatter any job for 48 hours. The real quality indicators are process questions asked before booking — wash sequence, decontamination steps, depth-gauge use — and how the paint looks under an inspection lamp at handover. Comparing two or three scoped quotes rather than one glossy promise is the cheapest quality control available.
Polishing too often
Every machine polish removes clearcoat, and clearcoat is a finite budget of roughly 40–60 microns for the car's whole life. Cars that get 'a quick buff' at every service end up with thin, UV-vulnerable paint within a few years. Protect more, polish less: correction should be an occasional reset, not routine maintenance.
Frequently asked questions
Is wax completely pointless here?
Not pointless, but short-lived. Carnauba-based waxes soften at temperatures a UAE bonnet exceeds daily in summer, so expect four to eight weeks of protection rather than the months you would get in Europe. On a garaged car, or as a cheap top-up over an existing coating, wax still has a role.
Can detailing remove the scratches from automatic car washes?
Usually yes, because brush-wash swirls are shallow and live entirely in the clearcoat. A single-stage polish clears most of them; heavier wash damage needs two stages. The catch is that returning to the same automatic wash reinstalls them within months, so pair the correction with a change in wash habits or the money is wasted.
Should I coat the car if it already has scratches?
Correct first, then coat. A ceramic coating is transparent and locks in whatever is under it, so coating over swirls preserves them under a hard layer that is tedious to polish through later. This is why reputable coating packages include at least a single-stage polish, and why suspiciously cheap coating offers usually skip it.
Do bird droppings and tree sap really damage paint that fast here?
Yes, and heat is the reason. A dropping is acidic, and on a 70-degree panel it etches a visible crater into clearcoat within hours, not days. Keep a bottle of quick detailer and a soft cloth in the car and lift droppings as soon as you see them; the etching they leave is one of the most common reasons cars end up needing spot correction.
Is summer or winter better for booking correction and coating work?
Winter is technically kinder — coatings cure more predictably below extreme heat, and outdoor mobile work is feasible all day. Summer work is fine in an air-conditioned or shaded studio, and demand dips mean better availability. What to avoid is major correction outdoors on a July afternoon, where product behaviour on hot panels becomes unpredictable.
Do you cover Riyadh City?
We cover Riyadh City and the surrounding Abu Dhabi communities. Message on whatsapp if you want a specific time confirmed first.