ttamamusually replies in minutes11:28
pinnedprice band AED 150–600duration 1–3 hourscovers Arjanemirate Dubai
need emergency electrician in arjan — today if possible11:28✓✓
Booking electrician in Arjan through tamam means seeing real vendor options before you commit — verified providers, transparent AED ranges, and the whole job coordinated in the app.11:29
typical ranges vendors quote around arjan —Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250Socket or switch replacement, per pointAED 150–250Chandelier installation with assembly, high ceilingAED 350–60011:30
that works. who actually turns up?11:31✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:32
The tower renter: what is yours, what is the building's, what is the landlord's
In an apartment, three parties share the electrical picture. The utility owns everything up to your meter. The building owns the risers, common-area wiring and the supply into your flat. Everything after your DB is the landlord's asset, and your tenancy contract decides who pays for repairs; the common UAE convention is that minor repairs below a threshold written into the contract fall to the tenant, while anything structural or aging-related is the landlord's problem. Read that clause before you spend anything, and photograph faults so the conversation stays factual.
Towers add a layer of process. Most managed buildings in Dubai Marina, JLT, Reem Island or Al Majaz require a work permit for any contractor entering the building, often restricted to weekday daytime hours, sometimes with a requirement that the company carries insurance. For a simple socket swap this is usually waved through at the security desk; for anything involving drilling or wall chasing, the building may want the landlord's no-objection letter first. Ask your building management what they need before the electrician is standing in the lobby.
What you should expect to pay
Rather than publishing one rate, tamam shows what multiple verified vendors charge for emergency electrician so you can pick the tier that fits the job and the budget.
Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250
Socket or switch replacement, per pointAED 150–250
Chandelier installation with assembly, high ceilingAED 350–600
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
Villa landscape lighting repair visitAED 250–550
The range narrows to an actual figure once a vendor sees the scope. You approve it before work starts.
Frequently asked questions
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
My whole flat lost power but the neighbours are fine. Who do I call?
First check your own DB: if the main isolator or RCD has dropped, reset it once. If the board is fully on but the flat is dead, the fault is likely at the meter or the building's riser, which is the utility's or building management's side. Call the building's maintenance desk or the utility's fault line; a private electrician cannot legally open that part of the installation.
Are my 110V appliances from the US safe to use here?
Not directly. The UAE supply is 220–240V, and plugging a 110V appliance in without a step-down transformer will damage it, often immediately. Small dual-voltage electronics like laptop chargers are fine with a plug adapter, but motors, kitchen appliances and anything with a heating element need a correctly rated transformer or, more sensibly, a local replacement.
How long does light fixture installation take, and can I supply my own fixture?
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
How do I know the electrician I am booking is actually qualified?
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Do you cover Arjan?
Yes — Arjan is covered across Dubai, with vendors who regularly work the area. Availability shows live in the app.
Avoid these
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Treating outdoor electrics like indoor electrics
Indoor-grade junction boxes in flowerbeds, unrated extension cords feeding garden lights and balcony sockets without covers all fail the same way: moisture gets in, the RCD starts tripping, and the search for the wet joint costs more than proper IP-rated fittings would have. Outdoors, specification is the economy.