ttamamusually replies in minutes11:42
pinnedfrom AED 150–600visit length 1–3 hourslocation JLT Cluster U, Dubaivendors verified
need electrician in jlt cluster u — today if possible11:42✓✓
Residents across JLT Cluster U book electrician through tamam because the model is simple — licensed vendors, transparent pricing, in-app tracking, and the same provider again next time if you liked them.11:43
typical ranges vendors quote around jlt cluster u —Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250Light fixture or ceiling fan installation, standard ceilingAED 150–350RCD or breaker replacement in the DBAED 200–45011:44
that works. who actually turns up?11:45✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:46
The tower renter: what is yours, what is the building's, what is the landlord's
In an apartment, three parties share the electrical picture. The utility owns everything up to your meter. The building owns the risers, common-area wiring and the supply into your flat. Everything after your DB is the landlord's asset, and your tenancy contract decides who pays for repairs; the common UAE convention is that minor repairs below a threshold written into the contract fall to the tenant, while anything structural or aging-related is the landlord's problem. Read that clause before you spend anything, and photograph faults so the conversation stays factual.
Towers add a layer of process. Most managed buildings in Dubai Marina, JLT, Reem Island or Al Majaz require a work permit for any contractor entering the building, often restricted to weekday daytime hours, sometimes with a requirement that the company carries insurance. For a simple socket swap this is usually waved through at the security desk; for anything involving drilling or wall chasing, the building may want the landlord's no-objection letter first. Ask your building management what they need before the electrician is standing in the lobby.
The landlord between tenants: a two-hour audit that prevents deposit disputes
A competent electrician can audit a one- or two-bedroom flat in a couple of hours: test every socket with a tester, press-test each RCD, check water heater elements for earth leakage before they become the next tenant's mystery trip, tighten DB terminals that loosen with thermal cycling, replace yellowed or cracked switch plates, and label the DB so the next occupant is not flipping breakers at random. In villas, add the garden circuits and the external water heater cupboards, which bake in the sun.
If you manage several units, consistency is worth more than any single cheap visit. Booking through tamam lets you rebook the same vendor across units and tenancy changeovers, so the person who labelled the DB in unit 704 is the one who answers when unit 1102 starts tripping, and the payment and job history sit in the app rather than in a folder of WhatsApp screenshots.
What it costs
electrician generally falls in the AED 150–600 band. Comparing several verified vendors on the same job description is what stops you overpaying.
Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250
Light fixture or ceiling fan installation, standard ceilingAED 150–350
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
Villa landscape lighting repair visitAED 250–550
These bands reflect typical jobs. Unusual scope gets quoted individually, still before you commit.
Frequently asked questions
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
My whole flat lost power but the neighbours are fine. Who do I call?
First check your own DB: if the main isolator or RCD has dropped, reset it once. If the board is fully on but the flat is dead, the fault is likely at the meter or the building's riser, which is the utility's or building management's side. Call the building's maintenance desk or the utility's fault line; a private electrician cannot legally open that part of the installation.
How long does light fixture installation take, and can I supply my own fixture?
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
Can electricians work evenings or weekends in apartment towers?
Emergency fault attendance is generally allowed at any hour, but planned noisy work like drilling is restricted by most building managements to weekday daytime slots, commonly somewhere between 8am and 6pm. Quiet work such as fixture swaps or DB diagnosis is often fine in the evening. Confirm your building's rules before booking a time you cannot use.
How do I know the electrician I am booking is actually qualified?
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Do you cover JLT Cluster U?
Yes — JLT Cluster U is covered across Dubai, with vendors who regularly work the area. Availability shows live in the app.