ttamamusually replies in minutes11:00
pinnedprice band AED 150–600duration 1–3 hourscovers Al Zahya Ajmanemirate Ajman
need electrician in al zahya ajman — today if possible11:00✓✓
electrician in Al Zahya Ajman: what it involves, what it should cost in AED, and how to book a licensed vendor who actually turns up when they said they would.11:01
typical ranges vendors quote around al zahya ajman —Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250Socket or switch replacement, per pointAED 150–250Light fixture or ceiling fan installation, standard ceilingAED 150–35011:02
that works. who actually turns up?11:03✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:04
What you should expect to pay
The honest answer on cost is a range, not a figure. For electrician the typical band is AED 150–600, and you see each vendor's position in it before committing.
Call-out with fault diagnosis (tripping breaker, dead circuit)AED 150–250
Socket or switch replacement, per pointAED 150–250
Light fixture or ceiling fan installation, standard ceilingAED 150–350
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
The range narrows to an actual figure once a vendor sees the scope. You approve it before work starts.
Frequently asked questions
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
Do I have to pay for electrical repairs in my rented apartment?
Check your tenancy contract for a minor-maintenance clause; the common UAE arrangement makes tenants responsible for small repairs up to a stated amount per incident, with the landlord covering wear-and-tear and anything structural. An aging water heater leaking to earth is wear, not misuse, so document faults with photos and dates before agreeing to pay.
How long does light fixture installation take, and can I supply my own fixture?
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
What is an RCD, and why does mine trip when the washing machine runs?
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
How do I know the electrician I am booking is actually qualified?
Legitimate operators work under a licensed company rather than as anonymous freelancers, and for regulated work they should name their utility approval without being pressed. Booking through tamam adds a layer, since listed vendors are verified and the job, payment and history are recorded in the app, which also makes it easy to rebook the same technician who already knows your board.
Do you cover Al Zahya Ajman?
Al Zahya Ajman is within our Ajman coverage. Open the app to see which vendors have slots near you today.
Avoid these
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Booking tower work without checking permit rules first
Many managed buildings turn contractors away without a work permit or landlord NOC, and some restrict noisy work to weekday hours. The result is a paid visit that ends in the lobby. One message to building management before you pick a slot avoids the wasted call-out.