ttamamusually replies in minutes11:21
pinnedrange AED 150–600time needed 1–3 hoursserving Al Salamatbook via app or whatsapp
need db board repair in al salamat — today if possible11:21✓✓
Getting electrician done in Al Salamat shouldn't involve three phone calls and a guessed price. Open tamam, compare verified vendors, pick your slot, done.11:22
typical ranges vendors quote around al salamat —New socket point as a spur on an existing circuitAED 180–350Light fixture or ceiling fan installation, standard ceilingAED 150–350Chandelier installation with assembly, high ceilingAED 350–60011:23
that works. who actually turns up?11:24✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:25
The landlord between tenants: a two-hour audit that prevents deposit disputes
A competent electrician can audit a one- or two-bedroom flat in a couple of hours: test every socket with a tester, press-test each RCD, check water heater elements for earth leakage before they become the next tenant's mystery trip, tighten DB terminals that loosen with thermal cycling, replace yellowed or cracked switch plates, and label the DB so the next occupant is not flipping breakers at random. In villas, add the garden circuits and the external water heater cupboards, which bake in the sun.
If you manage several units, consistency is worth more than any single cheap visit. Booking through tamam lets you rebook the same vendor across units and tenancy changeovers, so the person who labelled the DB in unit 704 is the one who answers when unit 1102 starts tripping, and the payment and job history sit in the app rather than in a folder of WhatsApp screenshots.
Cost of db board repair
Expect AED 150–600 as the working range for db board repair in Al Salamat. What moves it: job size, access difficulty, materials, and whether you want the value or premium tier.
New socket point as a spur on an existing circuitAED 180–350
Light fixture or ceiling fan installation, standard ceilingAED 150–350
Chandelier installation with assembly, high ceilingAED 350–600
RCD or breaker replacement in the DBAED 200–450
Full tripping-fault trace and repair, flat or villa zoneAED 300–600
The range narrows to an actual figure once a vendor sees the scope. You approve it before work starts.
What goes wrong
Resetting a tripping breaker over and over without finding the cause
A breaker that keeps dropping is doing its job; the fault is still there. Repeated forced resets stress the breaker and, in worn boards, can overheat the buswork behind it. Reset once after unplugging the circuit's appliances; if it will not hold, stop and book a diagnosis.
Fixing nuisance trips by fitting a bigger breaker or a less sensitive RCD
Upsizing protection to stop tripping removes the safeguard while leaving the fault. An oversized MCB lets cables run hotter than they are rated for inside walls, and a desensitised RCD stops protecting people from a leaking water heater. Any vendor proposing this as the fix is the wrong vendor.
Buying the appliance or fixture before checking the ceiling or the board
The induction hob that needs a dedicated circuit your DB cannot spare, the chandelier your gypsum ceiling cannot carry, the dimmer your LED lamps do not support: all cheaper to discover before purchase. A short survey visit or even photos sent ahead prevents owning hardware you cannot install.
Frequently asked questions
Why does my breaker trip every time it rains or the humidity spikes?
Moisture is getting into an outdoor fitting, balcony socket, external water heater cupboard or garden joint and leaking current to earth, which the RCD correctly detects. It feels random because it follows weather, not usage. An electrician isolates circuits at the DB and tests insulation resistance to find the wet point, then re-terminates it in a properly sealed enclosure.
Can a handyman add a new socket, or does that need DEWA approval?
A socket added as a spur from an existing nearby circuit is handyman-level work and needs no utility involvement, though in a rental you need landlord permission for anything cut into walls. A new circuit from the DB, a board upgrade or an increase in connected load crosses into approved-contractor territory with DEWA, SEWA, ADDC or Etihad WE, depending on your emirate.
How long does light fixture installation take, and can I supply my own fixture?
A standard fixture on a normal ceiling takes thirty to sixty minutes; chandeliers with assembly and high ceilings can run to two or three hours. Supplying your own fixture is normal and usually cheaper, just have it on site before the visit and mention ceiling height and material, since concrete slab and gypsum need different fixings.
What is an RCD, and why does mine trip when the washing machine runs?
An RCD cuts power within milliseconds when current leaks to earth, which is what stops a faulty appliance from electrocuting someone. Washing machines trip it when their heating element's insulation degrades, a very common failure in the UAE's hard water conditions. The fix is repairing or replacing the appliance, never swapping the RCD for a less sensitive one.
Is it worth adding RCD protection to an older building's board?
Yes, and it is one of the cheapest safety upgrades available. Many pre-2000s buildings in Deira, Ajman and UAQ still have boards with MCBs only, meaning nothing detects earth leakage from a failing heater or damaged cable. Adding RCD protection is a board-level job, so use a properly licensed electrician and expect a short power shutdown during the work.
Do you cover Al Salamat?
Yes — Al Salamat is covered across Abu Dhabi, with vendors who regularly work the area. Availability shows live in the app.