ttamamusually replies in minutes11:21
pinnedrange AED 100–500time needed 1–3 hoursserving Al Barsha Southbook via app or whatsapp
need curtain installation in al barsha south — today if possible11:21✓✓
Getting handyman done in Al Barsha South shouldn't involve three phone calls and a guessed price. Open tamam, compare verified vendors, pick your slot, done.11:22
typical ranges vendors quote around al barsha south —Standard call-out including first hour of labourAED 100–200Curtain rail or blind installation, per windowAED 100–250Flat-pack assembly, standard bed or chest of drawersAED 150–30011:23
that works. who actually turns up?11:24✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:25
What it costs
Rather than publishing one rate, tamam shows what multiple verified vendors charge for curtain installation so you can pick the tier that fits the job and the budget.
Standard call-out including first hour of labourAED 100–200
Curtain rail or blind installation, per windowAED 100–250
Flat-pack assembly, standard bed or chest of drawersAED 150–300
Large wardrobe assembly with anti-tip anchoringAED 250–500
Full shower or bathroom silicone resealAED 200–400
Parts and consumables, where they apply, are quoted separately and approved by you first.
TV mounting: forget the stud finder you saw on YouTube
Most TV-mounting advice online is written for North American timber-frame houses. UAE apartments and villas are built differently: exterior and structural walls are concrete block or poured concrete finished with plaster, while many internal partitions, especially in towers built after roughly 2005, are gypsum board on light-gauge metal studs. A timber stud finder is useless here. The professional method is a knock test first (block sounds dead, gypsum sounds hollow), then a magnet or metal-stud detector to map the studs at their usual 400 or 600 millimetre spacing.
On block or concrete, the job is straightforward: a hammer drill with a 6 or 8 millimetre masonry bit, nylon plugs matched to the screw, and the bracket pulls up rock solid. Expect 45-60 minutes for a fixed or tilting mount up to 65 inches, including unboxing, levelling and cable tidy-up. On gypsum, the calculus changes. A fixed mount for a mid-size TV can go onto heavy-duty toggle anchors spread across the plate, but a full-motion articulating arm concentrates leverage onto a few fixing points, and on gypsum that demands hitting at least two metal studs or, better, fitting a plywood backing board first. A technician who proposes screwing a swing arm straight into plasterboard with plastic plugs is telling you they have not done this long.
Hanging things on walls: gypsum, solid block and the hollow-block surprise
Every hanging job starts with the same question: what is this wall? Gypsum partition takes self-drive plasterboard anchors happily for light frames, up to roughly five kilograms per point, and spring toggles or metal cavity anchors for heavier pieces; anything genuinely heavy, a large mirror, a floating shelf meant to carry books, should land on the metal studs. Solid block or concrete takes standard nylon plugs and holds almost anything, the only cost being a hammer drill and some dust management.
For gallery walls and multi-frame layouts, watch for the laser line. A cross-line laser plus paper templates taped up for approval before drilling turns a two-hour trial-and-error session into forty minutes with zero spare holes. Good finish standard: frames level and aligned to the laser, no cracked plaster around fixing points, and every anchor flush, not proud of the wall.
Mistakes to avoid
Booking one small job at a time
Every visit carries the call-out minimum, so three single-job bookings can cost more than one half-day visit that clears ten jobs. Keep a running list on your phone and book when it reaches three or four items. Vendors also quote batched work more competitively because their travel time is spread across more billable tasks.
Skipping the building permit and losing the slot
In permit-controlled towers, a technician stopped at security is a wasted visit that you may still be charged for. Five minutes with building management before booking, asking about NOCs, service-lift rules and drilling hours, protects both your slot and your deposit with the building.
Fixing developer defects at your own cost
Cracked tiles, failed grout and misaligned kitchen units in a new handover are usually the developer's obligation during the defects liability period. Paying a handyman to fix them both costs you money and can undermine the official snag claim. Document and report first; hire for the jobs the developer never owed you.
Frequently asked questions
Do handymen bring their own tools and materials?
Tools, yes, always: drills, levels, anchors and consumables like screws and basic plugs are part of the service. Specific hardware is different: TV brackets, curtain rails, mirrors, shelves and replacement hinges are normally customer-supplied unless the quote says otherwise. Confirm the split when you accept the quote so nobody is standing in a hardware store mid-visit.
Can I hang a heavy mirror on a gypsum wall?
Yes, if it is fixed correctly. Light frames go on plasterboard anchors, but a heavy mirror needs to land on the metal studs behind the board or use rated cavity fixings across multiple points. If the technician cannot tell you which method they are using and why, pause the drilling.
How far ahead should I book?
In Dubai, Sharjah and Abu Dhabi, next-day slots are usually realistic and same-day is possible for simple jobs. In RAK, Fujairah and UAQ, where many teams travel from other emirates, one to two days ahead is safer. Move-in season, September and the weeks around school start, tightens availability everywhere.
What happens if the job takes longer than quoted?
It depends on whether the scope changed. If you added tasks on the day, expect the price to move, agree the addition before the extra work starts. If the scope is unchanged and the technician simply underestimated, a fixed quote should hold, which is one reason to get quotes against a full photo-documented list rather than a vague description.
Do handymen work weekends and evenings in the UAE?
Most vendors work Saturdays and many work Sundays, which suits commuting households, but tower rules can override this: plenty of buildings ban drilling on weekends or after 6pm. Quiet jobs, assembly, silicone, door adjustment, are usually fine any day. Check your building's noisy-work hours before booking a weekend slot.
Do you cover Al Barsha South?
We cover Al Barsha South and the surrounding Dubai communities. Message on whatsapp if you want a specific time confirmed first.