ttamamusually replies in minutes11:00
pinnedprice band AED 100–500duration 1–3 hourscovers Al Salamahemirate Umm Al Quwain
need picture hanging in al salamah — today if possible11:00✓✓
For anyone arranging handyman around Al Salamah, tamam removes the two annoying parts — finding someone trustworthy, and finding out the price before they arrive.11:01
typical ranges vendors quote around al salamah —TV mounting up to 65 inches (bracket supplied by customer)AED 150–350Curtain rail or blind installation, per windowAED 100–250Flat-pack assembly, standard bed or chest of drawersAED 150–30011:02
that works. who actually turns up?11:03✓✓
licensed vendors only — the licence and vendor ID land in this chat before anyone rings your bell.11:04
What you should expect to pay
picture hanging generally falls in the AED 100–500 band. Comparing several verified vendors on the same job description is what stops you overpaying.
TV mounting up to 65 inches (bracket supplied by customer)AED 150–350
Curtain rail or blind installation, per windowAED 100–250
Flat-pack assembly, standard bed or chest of drawersAED 150–300
Full shower or bathroom silicone resealAED 200–400
Door realignment and hinge repair, per doorAED 100–200
Nothing is charged until you have chosen a vendor and seen their number. There are no surprise call-out fees.
Anatomy of a call-out: what happens between the doorbell and the invoice
A well-run handyman visit has a fixed rhythm, and once you know it you can spot a professional inside five minutes. The visit starts with a walk-through: the technician looks at every job on your list before opening a toolbox, because the order of work matters. Dusty jobs (drilling into block) come before clean jobs (assembling furniture), and anything with a cure time (silicone) gets done early so the clock runs while other work continues. A pro will also tap-test your walls during this walk-through, because in the UAE the wall type decides the method for almost everything.
Next comes scope confirmation. The technician restates what will be done, what materials are needed, and whether anything on your list is actually outside a handyman's lane, wiring a new power point, for example, belongs to a licensed electrician under DEWA and municipality rules, and a good handyman says so rather than improvising. Then protection goes down: drop sheets under drilling points, and ideally a vacuum or dust catcher held at the drill hole, because red block dust stains light grout and carpet.
The kit in the van: what a properly equipped handyman carries
You can read a technician's standards from their kit before they touch a wall. The baseline for UAE work is a cordless hammer drill with masonry, wood and metal bits; a drill-driver with a clutch for flat-pack work; a cross-line laser and a traditional spirit level; a metal-stud detector and a strong magnet; and an anchor box that covers the local reality, nylon plugs in several sizes, plasterboard self-drives, toggles, cavity fixings and at least a few chemical-anchor options for hollow block.
The finishing and protection layer matters just as much: drop sheets, masking tape, a handheld vacuum or dust-catch attachment, sanitary silicone with a proper gun and tooling kit, hardwood dowels and wood glue for stripped hinges, and a step platform or ladder rated for ceiling work. What the technician usually does not carry is your specific hardware: TV brackets, curtain rails, mirrors and shelves are normally customer-supplied unless you agree otherwise in the quote, so confirm who buys what before the visit, not at your doorstep.
Judging the finished work: the five-minute walkthrough before the van leaves
Every job in this guide has an objective pass test, and the time to apply it is while the technician is still in your home. Pull firmly on every bracket, rail and mount, a proper fixing does not move at all, and a professional will do this pull test in front of you without being asked. Sight along rails and frames or ask for the laser to be held up one last time. Open and close every adjusted door at normal speed. Run a finger along silicone lines to check the edges are bonded (gently, and only if the bead has skinned). Count the holes: there should be exactly as many as there are fixings, and any abandoned holes should have been filled before the tools were packed.
Then look down. Dust and packaging are part of the job, not your problem after it: block-drilling dust vacuumed rather than swept into grout lines, cardboard and offcuts removed, protective film peeled off new hardware. Take photos of the finished work while everything is fresh, they are useful if anything settles or loosens in the first weeks.
Common missteps
Booking one small job at a time
Every visit carries the call-out minimum, so three single-job bookings can cost more than one half-day visit that clears ten jobs. Keep a running list on your phone and book when it reaches three or four items. Vendors also quote batched work more competitively because their travel time is spread across more billable tasks.
Letting anyone seal over old silicone
New silicone does not bond to old silicone, and mould trapped underneath grows straight through the fresh bead. If the technician is not spending most of the job on removal and drying, the reseal will fail within months. Ask to see the joint clean and dry before the new bead goes in.
Skipping the building permit and losing the slot
In permit-controlled towers, a technician stopped at security is a wasted visit that you may still be charged for. Five minutes with building management before booking, asking about NOCs, service-lift rules and drilling hours, protects both your slot and your deposit with the building.
Frequently asked questions
Can a handyman do electrical or plumbing work?
Only at fixture level: swapping a light fitting, changing a tap washer, fitting an appliance. New wiring, new power points, anything at the distribution board, or work on supply pipework needs a licensed electrician or plumber under DEWA, SEWA or ADDC and municipality rules. A good handyman will tell you where that line is rather than crossing it.
Do I need building permission before a handyman can drill?
In many Dubai and Abu Dhabi towers and masterplanned communities, yes: management requires a work permit or NOC, and often restricts noisy work to set weekday hours. Villas and most older buildings need nothing formal beyond a word with the watchman. Check with your building before booking, because a technician turned away at security still counts as a visit.
Is it cheaper to combine several small jobs in one visit?
Significantly. The call-out minimum, typically AED 100-200, is charged per visit, so five separate bookings pay that floor five times. A batched list turns the same jobs into one half-day visit around AED 300-500, and vendors quote batched work more keenly because the travel is amortised.
How far ahead should I book?
In Dubai, Sharjah and Abu Dhabi, next-day slots are usually realistic and same-day is possible for simple jobs. In RAK, Fujairah and UAQ, where many teams travel from other emirates, one to two days ahead is safer. Move-in season, September and the weeks around school start, tightens availability everywhere.
Do handymen work weekends and evenings in the UAE?
Most vendors work Saturdays and many work Sundays, which suits commuting households, but tower rules can override this: plenty of buildings ban drilling on weekends or after 6pm. Quiet jobs, assembly, silicone, door adjustment, are usually fine any day. Check your building's noisy-work hours before booking a weekend slot.
Do you cover Al Salamah?
Al Salamah is within our Umm Al Quwain coverage. Open the app to see which vendors have slots near you today.